Notice: Undefined index: linkPowrot in C:\wwwroot\wwwroot\publikacje\publikacje.php on line 1275
Publikacje
Pomoc (F2)
[49074] Artykuł:

Koncepcja zastosowania metody odniesieniowej do pomiaru odchyłki falistości elementów cylindrycznych

(A concept of using the V-block method for waviness deviation measurement of cylindrical parts)
Czasopismo: Pomiary Automatyka Kontrola   Tom: 60, Zeszyt: 9, Strony: 705-709
ISSN:  0032-4140
Opublikowano: 2014
 
  Autorzy / Redaktorzy / Twórcy
Imię i nazwisko Wydział Katedra Procent
udziału
Liczba
punktów
Paweł Zmarzły orcid logoWMiBMKatedra Technologii Mechanicznej i Metrologii*503.50  
Krzysztof Stępień orcid logoWMiBMKatedra Technologii Mechanicznej i Metrologii*503.50  

Grupa MNiSW:  Publikacja w recenzowanym czasopiśmie wymienionym w wykazie ministra MNiSzW (część B)
Punkty MNiSW: 7


Web of Science LogoYADDA/CEON    
Słowa kluczowe:

metoda odniesieniowa  odchyłka falistości  dokładność metody 


Keywords:

V-block method  coefficient of detectability  waviness deviation 



Streszczenie:

W artykule przedstawiono wyniki badań eksperymentalnych mających na celu weryfikację koncepcji zastosowania metody odniesieniowej do pomiaru odchyłek falistości powierzchni cylindrycznych w zakresie 16-50 UPR. Przeprowadzono badania porównawcze, polegające na ocenie odchyłki falistości wzorcowym przyrządem bazującym na metodzie bezodniesieniowej, a następnie za pomocą przyrządu opartego na metodzie odniesieniowej. Wyznaczono eksperymentalną dokładność metody odniesieniowej.




Abstract:

Measurement of waviness deviation of large size cylindrical parts using a widespread measuring device based on the non-reference method is significantly stymied. For this reason a concept of the V-block method adaptation to waviness measurement of cylindrical parts in industrial conditions was developed. The paper presents the results of experimental research aiming at the verification of the concept of applying the V-block method to waviness deviation measurement of cylindrical surfaces in the range 16-50UPR. Section 5 presents the construction and the principle of operation of the model measuring device ROL-2 (Fig. 4) developed to perform the V-block waviness measurement. This measuring device is based on the three-point reference method. Section 2 describes the main features with advantages and disadvantages of the non-reference method known as the radial method (Fig. 2). Section 3 contains a short characteristic of the V-block method (Fig. 3). In Section 4 there is presented the procedure of experimental research performed to calculate the V-block experimental method accuracy. For this reason comparative investigations were performed. They consisted in evaluation of the waviness deviation using the standard non-reference measuring device Talyrond 365 (Fig. 5), and next using the tested device based on the V-block method. The results of the statistical verification of the V-block waviness measurement show that the experimental method accuracy equals about 28,1% (Table 1) in relation to the non-references method.



B   I   B   L   I   O   G   R   A   F   I   A
[1] Adamczak S., Janecki D., Stępień K.: Cylindricity measurement by the V-block method – Theoretical and practical problems. Measurement, vol. 44, s. 164-173, 2011.
[2] Kuosmanen P: Predictive 3D roll grinding method for reducing paper quality variations in coating machine. Machine Design, vol. 2, 2004.
[3] Gapiński B.: Strategia pomiaru na CMM elementu obarczonego błędem okrągłości. PAK, vol. 56, s. 024-025, 2010.
[4] Cellary A., Jermak Cz. J., Majchrowski R.: Metody symulacyjne wyznaczenia błędów systemu do pomiaru odchyłki okrągłości metodą odniesieniową. PAK, vol. 56, s. 008-009, 2010.
[5] Hajtjema H., Bosse H., Frennberg M., Sacconi A., Thalmann R.: International comparison of roundness profiles with nanometric accuracy, Metrologia, vol. 33, s. 067-073, 1996.
[6] Adamczak S.: Pomiary geometryczne powierzchni, Wydawnictwo Naukowo-Techniczne, 2008.
[7] Adamczak S., Janecki D., Stępień K.: Qualitative and quantitative evaluation of the accuracy of the V-block method of cylindricity measurements. Precision Engineering, vol. 34, s. 619-626, 2010.
[8] Adamczak S., Zmarzły P., Krzysztof S.: Model matematyczny odniesieniowych pomiarów kształtu i falistości elementów okrągłych, Mechanik, vol. 7, s. 518-522, 2013.
[9] Adamczak S. Zmarzły P. Chmielik I. P.: Investigating mathematical models of waviness measurements of cylindrical elements by the V-block method through computer simulations, 11th International Symposium on Measurement and Quality Control 2013, Kraków-Kielce, 11-13 września 2013.
[10] Adamczak S., Janusiewicz A., Makieła W., Stępień K.: Statistical validation of the method for measuring radius variations of components f machine tool, Metrology and Measurement System, vol. 18, s. 035-046, 2011.